Manx SA7x Przewodnik Instalacji Strona 181
- Strona / 320
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
7
Installation and Preparation of the Add-On
SDI Storage Elements
This chapter describes the procedures for installing an add-on disk drive, for
example RA9x/SA7x in a DECArray300 cabinet. Procedures for using the
Digital lifting device and removing and replacing the cabinet front bezels,
operator control panels (OCPs), cabinet rear panel, cabinet top cover, and
cabinet kick plate are described. Finally, internal Standard Disk Interface
(SDI) cable and power cable routing and connections are included.
7.1 Site Preparation and Planning
Site preparation and planning are necessary before installing an DECArray300
cabinet system or add-on disk drive. The focus of this chapter is the
installation of additional SDI disk drives in an existing DECArray300
cabinet system; therefore, much of the site preparation and planning should be
complete. Please refer to Section 1.5 for Site Preparation. However, it will be
necessary to plan for the added weight and power requirements of additional
disk drives. It is recommended that ac power wiring for the computer system
be checked to determine adequate capacity for expansion. The wiring used by
Digital in this product conforms to Underwriter’s Laboratory (UL) Canadian
Standards Association (CSA) standards.
To prevent damage to equipment and personnel, make sure power sources meet
the specifications required for this equipment. For product specifications, refer
to Chapter 1.
The DECArray300 cabinet system will arrive at the site ready for installation.
WARNING
Hazardous voltages are present in this equipment. Installation and
service must be performed by trained Digital Multivendor Customer
Services personnel. Bodily injury or equipment damage may result
from incorrect servicing.
Installation and Preparation of the Add-On SDI Storage Elements 7–1
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Powiązane produkty i podręczniki dla Obudowy elektryczne Manx SA7x
Obudowy elektryczne Manx SA7x Instrukcja Obsługi
(128 strony)
(128 strony)
Obudowy elektryczne Manx SA7x Dokumentacja
(170 strony)
(170 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji